Research on fatigue properties of dissimilar metal ring welded joints

来源 :2013年国际焊接结构疲劳断裂学术会议 | 被引量 : 0次 | 上传用户：kathrynde

【摘要】

：

Austenitic stainlesssteel and low carbon steel in the stainless carbody were connected by ringwelded joints.The fatigue behaviors of such dissimilar metal ring weldingjoints were investigated in this

【作者】

：

Liu Wen Lu Lian-Tao Zhang Ji-Wang

【机构】

：

State Key Laboratory of Traction Power,Southwest Jiaotong University,Chengdu 610031

【出处】

：

2013年国际焊接结构疲劳断裂学术会议

【发表日期】

：

2013年1期

【关键词】

：

Ring welded joints fatigue crack propagation stress intensity factor

下载到本地 , 更方便阅读

下载此文赞助VIP

声明 : 本文档内容版权归属内容提供方 , 如果您对本文有版权争议 , 可与客服联系进行内容授权或下架

论文部分内容阅读

　　Austenitic stainlesssteel and low carbon steel in the stainless carbody were connected by ringwelded joints.The fatigue behaviors of such dissimilar metal ring weldingjoints were investigated in this paper.Tensile-shear loading tests conducted and the loading-life curve was obtained.

其他文献

Fracture analysis and its quality control of stainless steel high-temperature brazed pipe

In order to improve the high-temperature brazing quality of stainless steel pipe,the paper,by the example of the pipe union breaking failure in high-temperature brazing with the stainless steel pipe o

会议

Pipehigh-temperature brazingquality controltechnology improvement

Sensitivity analysis of the scaled boundary finite element method in cracked structures

The response sensitivity analysis of the scaled boundary finite element method(SBFEM),which has been effectively used in fracture problems,plays an important role in the probabilistic fracture mechani

会议

Sensitivity analysisthe scaled boundary finite element methodeigensensitivity

Review of Fatigue Analysis Methods for Welded Structures in Railway Locomotive and Vehicle

Bogie and car body are two of the most important welded structures in railway locomotive and vehicle.Bogie structure is usually welded by structural steel,while for car body,the parent materials inclu

会议

Fatigue analysiswelded structurerailway locomotive and vehicle

Ti-5Al-5Mo-5V-3Cr-0.5Fe合金的循环形变特征

源于合金VT22的新型亚稳态β钛合金Ti-5Al-5Mo-5V-3Cr-0.5Fe、(Ti-5553)，因其优于Ti-10V-2Fe-3Al(Ti-1023)的几大特点，例如，偏析敏感度低、淬透性好、强度优异和断裂韧性较高等优点已被选择应用于波音787飞机起落架转向架梁和飞机骨架结构件，也用于制造空客A380飞机发动机舱吊挂接头等关键承力部位.

会议

亚稳态β钛合金飞机关键结构件循环形变疲劳性能

焊接结构疲劳断裂仿真及寿命评定

传统强度设计思想的一个基本假设是把材料的初始状态视为无缺陷的均匀连续体。事实证明，根据这一思想设计的构件并不能保证其服役的安全可靠性。断裂力学通过连续介质力学的理论分析建立含裂纹构件的强度设计概念，提出设计计算方法及物理实验模型，探讨如何控制和防止结构的断裂破坏。

会议

疲劳断裂仿真焊接结构三维裂纹扩展寿命评估

Influence of laser dispersed treatment on rolling contact wear and fatigue behavior of wheel steel

The aim of this paper is to improve the rolling contact wear and fatigue resistance of ferrite-pearlite wheel steel by laser dispersed treatment.Such treatment creates isolated glazed regions on the s

会议

Laser dispersed treatmentrolling contact wearrolling contact fatigueplastic d

Fatigue properties of nickel-based superalloy components in electron beam welding

The paper investigates the tube-plate type components welded with full penetration electron beam,and the structural characteristic of the tube plate type component is introduced.

会议

Superalloysfatigue performanceelectron beam welding

Fatigue strength analysis of a welded bogie frame for Hong Kong metro

To ensure the application safety of a welded bogie frame for Hong Kong metro,fatigue strength was calculated and analyzed according to structure model.All the analyses were in accordance with the load

会议

Fatigue strengthwelded bogiefatigue limit diagram

5A06铝合金焊接接头超高周疲劳性能研究

采用自行研制的TJU-HJ-Ⅰ型超声疲劳试验装置对5A06铝合金无余高焊接接头在超长寿命区间的疲劳性能进行研究，探究断裂机理；对作为疲劳裂纹源的缺陷进行归类，分别研究不同缺陷对寿命的影响。

会议

5A06铝合金超声疲劳试验机焊接接头疲劳性能

50mm厚钛合金电子束焊接残余应力的轮廓法测量研究

本文采用轮廓法测试技术对50 mm厚钛合金电子束焊接接头残余应力进行测量，首先利用线切割方法将焊接构件沿构件沿中截面切开，然后用三坐标测量方法对切割后两个截面几何轮廓进行测量、求和取平均和光滑去噪声处理，最后建立有限元模型，将截面几何轮廓作为边界条件进行线弹性有限元求解获得残余应力分布。

会议

轮廓法残余应力钛合金电子束焊接

Research on fatigue properties of dissimilar metal ring welded joints

与本文相关的学术论文